How To Reset Nordictrack C700 Treadmill

by Kevinin Blog Postson Posted on

If your NordicTrack C700 treadmill is acting up, knowing how to reset NordicTrack C700 treadmill can often solve the problem. A reset is a simple first step that can clear error codes and restore normal function, saving you a service call.

How To Reset NordicTrack C700 Treadmill

There are two main methods to reset your C700. The first is a basic power cycle, and the second is a factory reset. You should always try the simple power cycle first, as it fixes most minor glitches without erasing your data.

Method 1: The Simple Power Cycle Reset

This process clears the treadmill’s temporary memory. It’s like restarting your computer. Follow these steps:

  1. Make sure the treadmill is completely stopped. The safety key should be removed from it’s console.
  2. Locate the power switch on the treadmill’s front or side, near the power cord. Turn this switch to the “OFF” position.
  3. Unplug the power cord from the wall outlet. Do not just turn off the surge protector; unplug the cord directly.
  4. Wait for at least 60 seconds. This allows any residual electrical charge to dissipate.
  5. Plug the power cord firmly back into the wall outlet.
  6. Turn the treadmill’s power switch back to the “ON” position.
  7. Reinsert the safety key. The console should light up and go through its startup sequence.

Test your treadmill. If it operates normally, the reset was successful. If problems persist, you may need to preform a factory reset.

Method 2: Performing a Factory Reset

A factory reset will restore the console to its original settings. Be aware that this will erase all your personal data, including workout history and saved user profiles. Use this method only if the power cycle didn’t work.

  1. Start with the treadmill powered ON and the safety key inserted. You should be at the main menu.
  2. Press and hold the “Stop” and “Speed +” buttons simultaneously. Hold them for about 5 to 10 seconds.
  3. You will see the console display change. It may show a confirmation message or simply begin the reset process.
  4. Release the buttons. The console will likely go blank and then reboot.
  5. The reboot may take a minute or two. You will see the NordicTrack logo and then the initial setup screen.
  6. Follow the on-screen prompts to set your language, units, and user information.

After the factory reset, your treadmill should behave like it’s new. Make sure to recalibrate if needed, which we’ll cover next.

When You Might Need to Reset Your Treadmill

Resetting isn’t a cure-all, but it helps with specific issues. Here are common signs that a reset could help:

  • The console is frozen or unresponsive to button presses.
  • Error codes (like E1, E2, etc.) appear on the display and won’t clear.
  • The incline or speed controls are not working correctly.
  • The console displays gibberish or has blank segments.
  • The treadmill beeps unexpectedly or acts erratically.

Important Steps After a Reset

Once your treadmill is reset, there’s a few things you should do to ensure it runs smoothly.

Recalibrate the Incline

After a factory reset, the incline system may lose its calibration. To recalibrate:

  1. Press and hold the “Incline +” and “Speed +” buttons while inserting the safety key.
  2. Keep holding until you hear the drive motor engage. The console will show a calibration message.
  3. The deck will move to its highest and lowest points. This takes about a minute. Do not interrupt it.
  4. When finished, the treadmill will return to the ready state.

Check for Software Updates (iFit Models)

If your C700 has iFit capability, check for updates after a reset. Connect it to your WiFi. The console may automatically prompt you to update, or you can check in the settings menu. Updated software can prevent future issues.

Inspect the Power Source

Many electronic problems stem from poor power. Plug your treadmill directly into a dedicated wall outlet, not a power strip or extension cord. Ensure the outlet is providing consistent power.

Troubleshooting Persistent Problems

If a reset didn’t fix your issue, the problem might be hardware-related. Here’s what to check:

  • Safety Key: Check for dirt or damage on the key and the port. A faulty connection can cause a no-start condition.
  • Power Cord: Inspect the entire cord for cuts, frays, or damage. A damaged cord is a safety hazard and needs replacement.
  • Drive Belt: If the belt slips or the motor strains, it might trigger errors. Check belt tension and alignment.
  • Console Wiring: Loose wires connecting the console to the motor board can cause intermittent faults. Unplug the treadmill and check connections (if you’re comfortable doing so).

For complex electrical or mechanical repairs, contacting NordicTrack support or a certified technician is the safest choice. They can properly diagnose issues with the motor control board or motor itself.

Preventive Maintenance to Avoid Frequent Resets

Regular care reduces the need for resets. A well-maintained treadmill is a reliable one.

  • Keep it Clean: Wipe down the console and deck after each use. Vacuum under and around the treadmill to prevent dust from entering the motor compartment.
  • Lubricate the Deck: Follow NordicTrack’s guidelines for lubricating the walking belt. A dry belt causes friction, strains the motor, and can lead to errors.
  • Tighten Hardware: Periodically check and tighten any bolts or screws on the handrails, console, and frame. Vibration can loosen them over time.
  • Use a Surge Protector: While you shouldn’t run the treadmill through a power strip, a quality surge protector can shield it’s electronics from voltage spikes.

Frequently Asked Questions (FAQ)

Where is the reset button on a NordicTrack C700?

There is no physical “reset button.” A reset is performed using the power cycle method or the button combination (Stop + Speed +) on the console.

How do I clear an error code on my NordicTrack treadmill?

First, note the specific error code. Then, perform a power cycle reset. This often clears temporary errors. If the code returns, it indicates a specific hardware problem that needs addressing.

Why won’t my NordicTrack C700 turn on after a reset?

Double-check that the power cord is securely plugged into a working outlet and the treadmill’s power switch is ON. Ensure the safety key is fully inserted. If it still won’t turn on, the power supply or internal fuse may be faulty.

Does resetting a NordicTrack treadmill delete iFit?

A factory reset will log out any iFit account and clear stored user data. However, the iFit software itself remains. You can simply log back in after the reset is complete.

My treadmill reset but now the incline is stuck. What should I do?

This usually means the incline system needs recalibration. Follow the incline calibration steps outlined earlier in this article. If that fails, the incline motor or its wiring could have a problem.

By following these steps, you can confidently manage your treadmill’s performance. Remember, regular maintenance is the best way to minimize the need for troubleshooting and keep your workouts running smooth.

Post author

Written by